CH-47D飞机大气数据测试仪适配器
NAV-AIDS公司自1960年代以来，专门为各种飞机提供空速管适配器和皮托管夹具，以及大气数据测试仪附件和套件。NAV-AIDS公司的主要产品包括空速管测试适配器和皮托管夹具，这些产品可以作为独立项目或飞机专用套件提供，包含所需的空速管和皮托管适配器、软管组件、预测试工具、控制台、备用密封件、润滑液、软管悬挂装置等。NAV-AIDS公司通过了ISO 9001:2015认证，确保其产品质量和服务的可靠性。
Pitot Test Adaptor
Part No. 18821-3 (2 req’d.)
These units fit the pitot probes located on the nose and when installed they will isolate and test each system separately or simultaneously.
Pre-Test Probe
Part No. PT11882 (2 req’d.)
When this unit is inserted into the adaptor and the extension hose is connected form the pneumatic generator, the complete system, tester, hoses and adaptors can be tested before fitting to the helicopter.
Static Test Adaptor
Part No. 21298M-370-4 (2 req’d.)
These units fit the static vents located on each side of the helicopter. The protective caps also act as pre-test adaptors.
Static Blanking Adaptor
Part No. 21298MB-370 (2 req’d.)
These units are used to blank off the static vent on the opposite side of the helicopter, thus completely closing off the system.
Pitot Test Hose Assembly
Part No. 47D-7270 (1 req’d.)
This hose is connected to each pitot inlet of the adaptors and is fitted with double acting quick disconnects for use when it is desirable to test only one pitot system. The connection for the pitot outlet of the pneumatic generator is included on this assembly.
Static Test Hose Assembly
Part No. 47D-5160 (1 req’d.)
This assembly attaches to the static test adaptors. The double acting quick disconnects operate in the same manner as those on the pitot test hose assembly. The extension fitting then connects to the static outlet hose of the pneumatic generator.
Hose Suspension Assembly
Part No. 532-4900 (2 req’d.)
One of these units is supplied with each kit to provide a means of support for static system test hose assembly.
Seal Kit - Part No. SK821 (2 req’d.)
Two sets of spare seals for pitot test adaptors are supplied with each kit.
Seals – Part No. 370-298-7M (2 req’d.) NSN: 5330-20-001-2814
Two spare seals for static test adaptors – P/N 21298M-370-4 are supplied with each kit.
Lubricating Fluid
Part No. LF5050 (1 req’d.)
This fluid is used to lubricate the glands of the pitot adaptor. It is recommended that a small amount be placed on the glands before installing the adaptor on the pitot probe.
Manual -
Part No. 444-47D-612 (1 req’d.)
One manual is supplied with each kit.
Case Assembly
The equipment is enclosed in this case assembly.
如果您需要用于连接大气数据测试仪与飞机皮托管和静压口的设备，需要选型号或是需要技术交流，请联系我们专业工作人员吧！
| Aircraft Type | Pitot Test Adaptor | Pitot Probe Part No. | Static Test Adaptor Blanking Adaptor | Miscellaneous Adaptor | Pitot Pre-Test & Assembly Integrity Fixture | Air Data Accessories Kit |
|---|---|---|---|---|---|---|
| CH-47D | 18821-3 | AN5813-2 |
21298M-370-4 21298MB-370* |
Vacu-Grip Assy. 532-4900 | PT11882 | ADA47D-612 |
| Aircraft | CH-47D |
|---|---|
| Air Data Accessories Kit | ADA47D-612 |
| Category | Other Helicopter |
| Miscellaneous Adaptor | Vacu-Grip Assy. 532-4900 |
| Pitot Pre-Test & Assembly Integrity Fixture | PT11882 |
| Pitot Test Adaptor | 18821-3 |
| Static Test Adaptor / Blanking Adaptor |
21298M-370-4 21298MB-370* |
| 飞机 | CH-47D |
|---|---|
| Air Data 附件套件 | ADA47D-612 |
| 类别 | 其他直升机 |
| 其他适配器 | Vacu-Grip Assy. 532-4900 |
| Pitot预测试和装配完整性夹具 | PT11882 |
| 皮托管测试适配器 | 18821-3 |
| 静态测试适配器 / 消隐适配器 |
21298M-370-4 21298MB-370*a |
AIR DATA ACCESSORIES KIT MODEL No. ADA47D-612 NSN: 4920-20-003-9098 CH-47D HELICOPTER - Proprietary Information -
This kit contains all the equipment required to test from source the complete pitot & static air data system on the CH-47D helicopter, as well as the means of pre-testing all adaptors and hoses prior to being fitted to the aircraft.
This kit contains all the equipment required to test from source the complete pitot & static air data system on the CH-47D helicopter, as well as the means of pre-testing all adaptors and hoses prior to being fitted to the aircraft.
Pitot Test Adaptor
Part No. 18821-3 (2 req’d.)
These units fit the pitot probes located on the nose and when installed they will isolate and test each system separately or simultaneously.
Pre-Test Probe
Part No. PT11882 (2 req’d.)
When this unit is inserted into the adaptor and the extension hose is connected form the pneumatic generator, the complete system, tester, hoses and adaptors can be tested before fitting to the helicopter.
Static Test Adaptor
Part No. 21298M-370-4 (2 req’d.)
These units fit the static vents located on each side of the helicopter. The protective caps also act as pre-test adaptors.
Static Blanking Adaptor
Part No. 21298MB-370 (2 req’d.)
These units are used to blank off the static vent on the opposite side of the helicopter, thus completely closing off the system.
Pitot Test Hose Assembly
Part No. 47D-7270 (1 req’d.)
This hose is connected to each pitot inlet of the adaptors and is fitted with double acting quick disconnects for use when it is desirable to test only one pitot system. The connection for the pitot outlet of the pneumatic generator is included on this assembly.
Static Test Hose Assembly
Part No. 47D-5160 (1 req’d.)
This assembly attaches to the static test adaptors. The double acting quick disconnects operate in the same manner as those on the pitot test hose assembly. The extension fitting then connects to the static outlet hose of the pneumatic generator.
Hose Suspension Assembly
Part No. 532-4900 (2 req’d.)
One of these units is supplied with each kit to provide a means of support for static system test hose assembly.
Seal Kit - Part No. SK821 (2 req’d.)
Two sets of spare seals for pitot test adaptors are supplied with each kit.
Seals – Part No. 370-298-7M (2 req’d.) NSN: 5330-20-001-2814
Two spare seals for static test adaptors – P/N 21298M-370-4 are supplied with each kit.
Lubricating Fluid
Part No. LF5050 (1 req’d.)
This fluid is used to lubricate the glands of the pitot adaptor. It is recommended that a small amount be placed on the glands before installing the adaptor on the pitot probe.
Manual -
Part No. 444-47D-612 (1 req’d.)
One manual is supplied with each kit.
Case Assembly
The equipment is enclosed in this case assembly.
如果您需要用于连接大气数据测试仪与飞机皮托管和静压口的设备，需要选型号或是需要技术交流，请联系我们专业工作人员吧！
