Power Integrity Demo at embeddedworld2019 Are you seeing ALL the noise from your power rails? Lee Morgan, Technical Marketing Manager in EMEA, demos one of our power integrity setups with a6Series MSO, our new Power Rail Probes, and an …
Power Supply Rejection Ratio on an Oscilloscope Learn how to get optimal results from your power supply design by checking the power supply rejection ratio. This video covers how DC-DC  converters or low voltage drop-out regulators (LDOs) …
How to Measure Power Rail Current with a Shunt Resistor Make extremely accurate power rail measurements using two Tektronix power rail probes, a Keithley DMM6500 touchscreen Digital Multimeter, and ultra-low-noise6Series mixed signal oscilloscope …
Automotive Ethernet PAM3 and Signal Separation Introduction Automotive Ethernet with PAM3 introduces new test challenges. Tektronix' new, innovative, non-intrusive Signal Separation simplifies Automotive Ethernet testing and set-up, providing advanced …
Demonstration of Automated Automotive Ethernet Compliance Test System Test automation may be used to check automotive Ethernet transmitters for compliance with the BroadR-Reach, 100BASE-T1 (P802.3bw), and 1000BASE-T1 (802.3bp) standards. This demonstration shows the …
52s Spectrum View on the 5 and6Series MSOs How independent time and frequency controls beat traditional FFTs.
Analyzing turn on behavior of a spread spectrum clock with Spectrum View on 4, 5 and6Series See how Spectrum View provides ease-of-use and the ability to achieve optimal views in both RF and Time domains simultaneously when analyzing the turn on behavior of a spread spectrum clock.  This …
Tips and techniques for setting up your Tektronix 4 Series, 5 Series or6SeriesMSOdisplay Watch how easy it can be to setup and analyze waveform behavior using the highly intuitive touch interface. Setting up your measurement and debugging your system has never been easier with the …
Capturing a Clock Frequency Glitch With RF vs Time Trigger See how an edge trigger on the RF Frequency Deviation vs Time trace isolates and captures a short duration transient in the frequency of a clock signal.  The Spectrum View capability on the 4, 5 …
How to use Callouts on the 4 Series, 5 Series and6Series Mixed Signal Oscilloscopes Learn how to annotate test results and methods with “Callouts” for easily documenting important information when sharing data across a team, recreating a measurement at a later date, or delivering …
Low amplitude RF emission analysis with RF vs Time Triggering See how the RF vs Time hardware triggering capability (Spectrum View) on the 4, 5, and6SeriesMSOoscilloscopes can capture a low amplitude RF emission.  This video focuses on the low amplitude …
Spread Spectrum Clock Analysis With RF vs Time Triggering See how to stabilize a hardware trigger on the up-down chirp pattern of a spread spectrum clock using a Frequency Deviation vs. Time trigger.  The Spectrum View capability on the 4, 5 and6Series …
Finding root cause of EMI signals with Spectrum View See how to track down the source of transient RF/EMI emissions with Spectrum View and the RF vs Time triggering capabilities. Clearly determine which PCB signals are causing EMI emissions so that …
Triggering on an ASK (Amplitude Shift-Keying) Signal with Spectrum View Watch this short demo of RF vs Time hardware trigger to see how an ASK (Amplitude Shift-Keying) signal changes over time.  The Spectrum View capability on the 4, 5 and6SeriesMSOoscilloscopes …
Making Power Rail Measurements See the ultra-low noise performance of the TPR4000 Power Rail Probe, and how it can be used for measuring DC power rail noise in microvolts, especially when paired with the6SeriesMSO…
Automotive Ethernet 100BASE-T1 Signal Separation and Protocol Decoding Demo A demonstration of 100BASE-T1 Automotive Ethernet protocol decoding on a6SeriesMSOoscilloscope.  This video shows how full-duplex 100BASE-T1 can be separated and decoded without breaking the …
A New Way of Performing Multi-Channel Spectrum Analysis on an Oscilloscope If you're doing mixed frequency/time domain work, Spectrum View makes it easy. Learn how to set up 5 and6Series MSOs to display synchronized time and frequency domain views on multiple channels …
How to Use Oscilloscope Visual Triggers Build complex waveform triggers simply by drawing shapes Learn how to quickly capture bursts just by drawing a couple of boxes, and how to apply logic and add more shapes to capture increasingly complex waveforms. See how visual triggers work on the 5 …
How to Control a Tektronix Oscilloscope Over a LAN Learn how to use the eScope function to remotely control a Tektronix oscilloscope over a network without any special software. This video shows how to find the IP address of the scope and use a …
The Science Behind The Low Noise What's the big deal with low noise? We talked to our engineers about how they achieved ground-breaking noise performance in the6Series Mixed Signal Oscilloscope.
How to change the font size on the 4 Series, 5 Series or6SeriesMSOdisplay Watch how to easily change the font size used on your 4/5/6 SeriesMSOwith just a few clicks. This will make it easier to read measurement values at a distance from your scope or maximize the …
MIL-STD-1553 bus support Learn how 5 and6SeriesMSOMixed-Signal Oscilloscopes and the optional embedded serial bus analysis software provide unparalleled system visibility by decoding MIL-STD 1553 messages, triggering …
Comparing phase on RADAR pulses with the6SeriesMSOAn AWG70002B was used to create a pair of 20us wide RF pulse trains at 3.85GHz. One pulse train has a constant/unchanging phase – this is our reference and is applied to Ch1. The other pulse …